降解式晾干機

◆車輛優缺點 Product features

※具備穩定性高一樣的的排氣重壓和露點

1.吸咐塔之較高與直徑怎么算經實驗報告畢竟精密五金算出，塔床內壓小，確定了解壓縮有毒氣體干燥的劑5秒的排斥周期，能夠滿足生產設備氣的露點規范。

2.30％的晾干的劑的余量，代替補償費晾干的劑的大自然老化測試，狠抓晾干的。

3.大分散器，抓實環流透亮利用低溫干燥劑層，去掉溝流現狀。

※復蘇氣量耗率高于14％

1.好的機筒設計構思，保留100％的離心分離熱能，補充的熱能使用增強粉碎時間段的粉碎氣溫暖，不斷提高機械的解吸專業能力，會使粉碎更徹底。

2.粗糙和二次利用利用反方向對流傳熱實施方案，濕水汽流下來干的吸劑限期果最合適。二次利用氣口含濕量有效控制在亞供大于求環境，使排氣管消聲器器及排氣管的通道無結霜現象之慮。

3.可按照其干澡機的行駛負載電阻標準調高二次利用氣消耗量，切實保障二次利用氣團反復動態平衡，二次利用壓力差低至臨界值。

※粗糙劑食用使用年限長

1.比較適合的機筒長寬比，使氣體經過空氣太干劑層的流體密度和精力始終保持好的的情況，足夠進一步強化空氣太干劑的功能。

2.適當的體統配值，在環流來到機筒前，經除油處里適時清掉環流中內含油份物與重破壞物，盡量不要非常干燥劑層受破壞。

※儀器用于了構思高品級電動及氣動彈簧閥和耐用的全電子技術可c語言編程序修改器，人與機器網頁友善，自然連著表示雙塔操作，嵌套循環時間是現場可編，出產修改10min。蝶閥期短短50萬次拉伸動作。

※鍋筒表面作冷鍍鋅管金屬防腐加工處理，10年不上銹。

※運動正確、特性動態平衡、的操作簡約，裝有不用地基。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆重點技術規格 Main technical parameters